Our crew installs spray foam insulation in Milton, mostly on rim joists and basement walls, and we put it next to foam board and batts before you decide. We drive in from Mississauga, about 13 km from the middle of Milton.

Spray foam in Milton homes

Most of Milton is suburban. Highway 401 cuts through the town, with the mainly rural and industrial land to the north and the mainly residential and commercial land to the south, so most family homes are on the south side of the highway.

Spray foam suits a few spots in a house. It is not the answer for every one. Take an unfinished basement: its walls can be insulated three ways, and each way asks something different of the room.

Closed-cell spray foam on the concrete

Closed-cell spray foam goes straight onto the concrete and sets hard, and that layer doubles as the vapour retarder. You get the most insulation for the least depth, so the room loses the least floor space. The price follows the area and the thickness sprayed. While it goes on, the basement has to be emptied and then aired out.

Rigid foam board behind a stud wall

We fasten foam board to the concrete, tape every seam and frame a stud wall in front of it. It needs a little more depth than spray foam, with far less mess. It works best on a fairly flat wall that doesn't have many pipes or ducts in the way.

Fibreglass or mineral wool batts

Batts fit between studs set slightly off the wall, with a sealed vapour barrier on the room side. Most people have seen this method before, and it is the easiest to open up later. It also takes the most depth, and it is only as good as the sealing at each seam, outlet and window.

Which one we would choose for a basement wall

For a dry, even wall we would pick foam board with a stud wall in front. It keeps damp air off the framing, and nobody has to spray the whole wall. If the concrete is uneven or crowded with pipes, closed-cell foam fits better. You make the call. Our basement insulation page goes through each option in more detail.

Attic top-ups

We start an attic top-up at the hatch. We lift it, push a tape measure down to the ceiling drywall in several places and write down how high the existing blown fibreglass or batts sit against the joists. Only then do we suggest anything.

When the old layer is dry and even, we blow new fibreglass over it. Baffles at the eaves keep the soffit vents open. We staple depth markers to the joists so you can check the finished level from the hatch later.

A newer house may already be close to full depth. If yours is, we will tell you. Then air sealing around pot lights and plumbing stacks may do more for a cold upstairs room than more fibreglass would. Our attic top-ups page compares blowing over the old layer with clearing it out first.

How far we come

Milton is about 13 km from us, and we come out for every service we offer, whether that's one rim joist or a whole basement. The drive doesn't change how we measure or write up the job. You get the same tape measure and notepad, and a written quote that lists each spot and the material we would put there.

Rim joist spray foam and air sealing

The rim joist is the band of framing that sits on the sill plate along the top of the basement wall, and it is the one spot where closed-cell spray foam is our first choice. Batts cut to fit the joist bays leave gaps, and air moves behind them. Foam board pieces can work, but every edge has to be sealed with canned foam.

Closed-cell foam fills each joist bay in one pass. It seals the joint at the sill plate and keeps moist indoor air away from the cold wood. Your rim joist may already have batts. If they are dry and you don't feel a draft at the baseboard above, leave them where they are.

We use the same foam and sealant on the gaps where plumbing stacks and wiring run up through the top plates into the attic. You'll find every service we offer around the house on our home page.

About Milton: Milton, ON on Wikipedia ยท Milton on Google Maps

FAQ

Insulation questions from Milton

Yes. Our crew installs closed-cell spray foam insulation in Milton, mostly on rim joists and on basement walls before they get finished. We measure each spot first, then put foam next to board and batts so you can compare them.

We usually pick foam before finishing a Milton basement, either closed-cell spray foam or rigid foam board, because it keeps damp air away from the concrete and the framing. Batts work too, as long as the vapour barrier in front of them is sealed carefully at every seam. They take more depth out of the room, so we measure the wall and show you both before you choose.

Milton is about 13 km from us. The residential south side, below Highway 401, sits well inside the area we cover for every service.

Get a quote

Request an insulation visit in Milton

Call (437) 563-1419 or send the form, and tell us what you notice in the house: a cold floor over the garage, a draft at the baseboard, a damp smell in the basement. We measure the spots that matter and give you a written quote with the options side by side.

Call Text Quote