We install spray foam insulation in Lisgar, about 6 km from us. This page covers the L5N postal area, which includes Lisgar and part of Meadowvale. Before we suggest anything, we measure your attic and basement.

Houses from 1986 onward

Lisgar's first housing went up in 1986, starting with Trelawny, where the homes sit on cul-de-sacs with asymmetrical lots around Trelawny Circle. By 1996 the neighbourhood was nearly two-thirds built out. Highway 407 runs along its west side, Highway 401 along the north, Tenth Line on the east and Britannia Road on the south.

Houses of that age are among the 1980s and 1990s homes we work on. The build year doesn't tell us how a particular house was built or insulated, though. Two houses on the same Trelawny cul-de-sac can have very different attic depths, depending on what each owner has added over the years. Yours may not need any work. We find that out with a tape measure, not from the year the house went up.

Attic or rim joist: which first

In a house of this age we check two spots first: the attic floor and the rim joists. If yours needs both, here is how they compare.

  • Attic floor. If you can see the tops of the ceiling joists through the old layer, we would blow fibreglass over what's already there as an attic top-up. You could use batts instead, but batts tend to leave gaps at the joists and around pot lights. Blown fibreglass fills those gaps, and the ceilings below stay as they are. We set baffles at the eaves first so the new layer doesn't block the soffit vents. You may notice the upstairs bedrooms staying closer to the temperature of the rest of the house.
  • Rim joists. The rim joists are the band of framing that sits on the sill plate on top of the foundation wall, and outside air can get in along that line. There are three ways to do them: closed-cell foam, foam board cut to fit each joist bay and sealed at the edges, or fibreglass batts. Air moves around batts. Foam board works, but only if every bay is cut and sealed carefully. Closed-cell foam fills the bay and stops air in the same layer, so that's our pick for this spot. You may notice less draft at the baseboards and a warmer floor along the outside walls.

Asking the City

Insulation isn't on either list on the City's building permit page: not the projects that need a permit, and not the ones that don't. Finishing a basement to create rooms or living space does need one. So if foam on the basement walls is part of a finishing job, the permit question covers that whole job.

Zoning regulations still apply even when no permit is needed. If you want an answer for your own house in Lisgar, call 311 and ask the City.

A written quote

The quote lists each spot we measured, the material we would use there, the other options we looked at and why we chose one over the rest. Where spray foam insulation is the pick, the quote names the bays that get it and the spots that get something else. If part of the job has to wait for another trade, say a roofer to fix a leak, we note that on the quote too.

Churchill Meadows sits right next to Lisgar, and we do the same rim joist and attic work there. Meadowvale Village is a short drive away, and we do basement and garage work there too. East Credit is close too, and we compare the same foam and attic options there that you see above.

Local details for Lisgar

About Lisgar: Lisgar, ON on Wikipedia ยท Lisgar on Google Maps

FAQ

Insulation questions from Lisgar

The first houses in Lisgar went up in 1986, starting with Trelawny, and by 1996 the neighbourhood was nearly two-thirds built out. Those early homes sit on cul-de-sacs with asymmetrical lots around Trelawny Circle. The age of your house is a starting point, but we still measure the attic and basement before we suggest anything.

It could be either, and some Lisgar houses need neither, so we measure before saying. For a thin attic floor we would do a blown fibreglass top-up. For bare rim joists we would use closed-cell foam. We check the attic depth and look at every rim joist bay, then put both options side by side on the quote.

The City's building permit page doesn't say. Insulation isn't on its permit-required list or its no-permit list, so call 311 for a straight answer about your house. Finishing a basement to create rooms or living space does need a permit, and zoning regulations still apply when no permit is needed.

Get a quote

Request an insulation visit in Lisgar

Call (437) 563-1419 or send the form, and tell us what you notice in the house: a cold floor over the garage, a draft at the baseboard, a damp smell in the basement. We measure the spots that matter and give you a written quote with the options side by side.

Call Text Quote