Spray Foam Insulation in Erin Mills, ON
Rim joists, attic floors and garage ceilings in Erin Mills. We measure first, then put the options side by side.

We install spray foam insulation in Erin Mills, along with attic top-ups and basement insulation, and Erin Mills is about 5 km from us. This page covers the L5L postal area, which takes in Erin Mills and the Western Business Park. Before we suggest anything, we measure what your house already has.
Built from the south end up
Erin Mills began in the early 1970s as a planned 'new town' on over 7,000 acres of farmland. The first section to go up was the stretch between Dundas Street and Burnhamthorpe Road. Today the neighbourhood runs from Dundas Street in the south to roughly Britannia Road in the north, and from the Oakville border in the west to the Credit River in the east.
For insulation, that building order is worth knowing. A house near the south end is among the oldest in Erin Mills, and its attic and basement may still hold whatever went in when it was new. A house further north went up later and may need much less, sometimes nothing at all. Which options make sense depends on the house, so we look at it before we put any of them forward.
Two houses, two sets of options
Take one house close to Dundas Street and another up toward Britannia Road. The work each one needs can be quite different.
- An older south-end house: the attic floor may be thin enough that the tops of the ceiling joists show, and the rim joists in the basement may be bare. In that case we would blow fibreglass over the existing layer as an attic top-up and spray closed-cell foam on the rim joists.
- A newer north-end house: the attic may already be at a good depth. The only job left may be the rim joists, or the garage ceiling under a bonus room if that ceiling is coming open anyway.
Foam where it fits, not everywhere
Spray foam insulation earns its place in three spots in an Erin Mills house and is the wrong pick in a fourth.
The rim joist is the strip of framing that sits on the sill plate. You can insulate it with closed-cell foam, with foam board cut to fit and sealed at the edges, or with fibreglass batts. Batts let air slip around them. Foam board works, but every piece has to be cut and sealed between the joists by hand. Closed-cell foam fills the bay and stops the air in one layer, so that is our choice for this spot.
On a garage ceiling under a bonus room, foam is only an option when the joist bays are open. A finished ceiling has to come down first. Our crew insulates the joist bays, and whoever puts the drywall back brings the ceiling back to fire-separation standard; the quote names who that is. We never blow or pack insulation through a closed garage ceiling.
For a basement wall you have not finished yet, there are two routes: closed-cell foam sprayed straight onto the concrete, or foam board with a stud wall and batts in front of it. Foam takes up less floor space and puts the air and vapour control right on the concrete. The board-and-batt wall is deeper and takes more steps, though some homeowners prefer those materials.
On an open attic floor, we would not use foam. Blown fibreglass spreads evenly across the joists, goes straight over the old layer, and can be topped up later without disturbing anything.
Old insulation and what is under it
Wet or rodent-damaged insulation in an attic or basement comes out before anything new goes in. Wet insulation points to a leak, and the right trade, a roofer or a plumber, fixes the cause first. Rodents are a job for a pest-control company, which deals with the animals and how they got in before we arrive; we do not do that part. After that, our crew handles the insulation removal and lays the new layer on a dry, clean surface.
Three other areas we serve sit right beside Erin Mills. Sheridan is next door, and we do the same rim joist and attic work there. Clarkson and Creditview are a short drive away, and we handle basements and garage ceilings there the same way.
Local details for Erin Mills
- Postal codes: L5L
- Distance: About 5 km away in a straight line
- Nearby: Sheridan, Clarkson, Creditview
About Erin Mills: Erin Mills, ON on Wikipedia ยท Erin Mills on Google Maps
FAQ
Insulation questions from Erin Mills
The area between Dundas Street and Burnhamthorpe Road came first, starting in the early 1970s. Erin Mills was planned as a new town on over 7,000 acres of farmland, and it filled in north toward Britannia Road from there. The houses in that southern section are the oldest in the neighbourhood.
It may need both, each in its own spot: blown fibreglass on the attic floor and closed-cell spray foam at the rim joists. Blown-in suits an open attic because it spreads evenly over the existing layer. Foam suits the rim joist because it fills the bay and stops air movement in one pass. We measure the attic depth and check the rim joists before recommending either.
Yes. If it is wet or rodent-damaged, we take it out before the new insulation goes in. A roofer fixes any leak first, and a pest-control company deals with the animals before we start. If the old insulation is dry and intact, a top-up can usually go right over it.
Get a quote
Request an insulation visit in Erin Mills
Call (437) 563-1419 or send the form, and tell us what you notice in the house: a cold floor over the garage, a draft at the baseboard, a damp smell in the basement. We measure the spots that matter and give you a written quote with the options side by side.






