Spray foam insulation in Sheridan is work our crew does about 7 km from us. This page is for L5K, which is West Sheridan. East Sheridan shares L5H with Port Credit and Lorne Park. In every house we measure each spot first, then put the options next to each other.

Ceilings first, then foam

In some houses, the first spots worth measuring are in the ceiling, not down in the basement. Warm air rises out through gaps around pot lights, plumbing stacks and the attic hatch, and foam lower in the house won't stop any of it. Each of these spots can be closed two ways. Both are listed below, along with the one we would pick.

This work is called air sealing. If your ceiling has gaps like these, we seal them before any foam goes in anywhere else. Insulation laid over an open gap just lets the air carry on through it.

  • Pot lights: a fitted cover boxed over the fixture from the attic side, or a sealed housing installed by an electrician. Where the attic leaves room to work, we would go with the cover.
  • Plumbing stacks: a flexible collar around the pipe, or canned foam packed into the hole in the ceiling. We would use the collar, because the pipe shifts a little as it heats up and cools down.
  • Attic hatch: foam board fixed to the back of the panel, or a new insulated hatch cover. If the hatch is still sound, we would add the board.

Foam at the band joist

There are three ways to insulate the rim joist, which is the board sitting on the sill plate around the edge of your basement ceiling.

Of the three below, we'd pick closed-cell foam. The bays are small, awkward and cold, and foam gets into the corners that board and batts leave open. If your basement ceiling is already finished, the edge of it has to come open first, and the quote says who takes care of that. There's more detail on the rim joists page.

  • Closed-cell spray foam: we spray it into each joist bay. It fills the corners and the gap at the sill plate, and it is its own vapour barrier. While it goes on, the bays need to be clear and the strip along the basement walls emptied.
  • Foam board: cut to fit each bay, then sealed around the edges with canned foam. There's less mess. Every bay has to be cut and fitted by hand, though, and that labour is what drives the price.
  • Fibreglass batts: pressed into the bays. They go in easily, but damp indoor air can get past them to the cold rim and leave condensation behind.

If the attic is thin

When an attic is thin, we blow fibreglass over the layer that's already there, after the air sealing underneath is done. Before blowing, our crew puts baffles in at the eaves so the new layer stays off the soffit vents. Then we staple depth markers to the joists, and you can check the finished depth yourself from the hatch.

You could also roll batts across the top instead, but they leave seams and don't sit well around wiring and truss webs. We would choose blown fibreglass. If your attic already measures well, we'll say so and leave it alone. A newer house may not need attic top-ups at all.

From a look to a quote

Your written quote lists every spot we measured, how we would do each one, the material, and anything that has to happen before or after, like a finished ceiling that needs opening up. If a spot has two sound options, we put both on the page and you choose. We price spray foam insulation the same way in every area we cover.

Erin Mills is the next area over, and the rim joist and attic options there are the same. Clarkson is close by too, with the same garage and basement choices you've read about here. Creditview is also nearby, and we measure and quote foam and basement work there in the same order.

Local details for Sheridan

FAQ

Insulation questions from Sheridan

No. This page is about West Sheridan, in L5K. East Sheridan is part of the L5H postal area, which it shares with Port Credit and Lorne Park. Either way, each spot in the house has the same options, from the attic hatch down to the rim joist.

Yes. If there are open gaps in the ceiling around pot lights, plumbing stacks or the attic hatch, we seal those first. Foam in the basement won't keep warm air from escaping out the top of the house. With the ceiling closed up, rim joist foam and an attic top-up, if you need one, can do their job.

Yes. Both jobs can go on one written quote and be booked for the same visit. Each job gets its own line with its method and material, so you can take one and skip the other. Whichever you choose, the ceiling gets air sealed before the attic top-up.

Get a quote

Request an insulation visit in Sheridan

Call (437) 563-1419 or send the form, and tell us what you notice in the house: a cold floor over the garage, a draft at the baseboard, a damp smell in the basement. We measure the spots that matter and give you a written quote with the options side by side.

Call Text Quote