We install spray foam insulation in Etobicoke on rim joists, basement walls and garage ceilings, after measuring what is already there. Our crew drives in from Mississauga, about 19 km from the middle of Etobicoke.

Spray foam in Etobicoke houses

Etobicoke's residential areas are primarily single-family dwellings. In a single-family house, one owner decides every spot we measure, whether it is the rim joist or the attic floor.

Central Etobicoke includes Etobicoke's most exclusive neighbourhoods, with fine housing stock and many large treed properties. If your basement or a bonus room is already finished, start by asking how much of the finish has to come down to reach the spot. The answer often picks the material before anything else does.

Most spots can be done one of three ways:

  • Closed-cell spray foam insulates, air-seals and holds back vapour in a single layer. The cavity has to be open, and the room cleared and ventilated while the foam cures. Between the material and the spray rig, it is the dearest of the three.
  • Foam board is rigid sheet, cut to fit, with every edge sealed in canned foam. It makes less mess, but any seam sealed carelessly lets air through.
  • Fibreglass batts cost the least per bay. They do not stop air, so they need a separate air and vapour barrier, and in odd-shaped cavities they slump.

Rim joists and basement walls

On the rim joist, we would use closed-cell foam. The rim joist is the band of framing that sits on the sill plate around the top of your basement wall. It is divided into short joist bays, usually crowded with wires and pipes. Board cut to each bay works, as long as every edge gets sealed. Batts pushed into the bay leave the cold framing exposed to damp basement air, and mould can start behind them. Sprayed foam fills the bay and closes the gap at the sill plate in one pass. Our page on insulating rim joists covers each method in more detail.

In an unfinished basement, nothing has to come down to reach the rim joist. In a finished one, the ceiling drywall along the outside walls comes off first, and at that point foam board through a smaller opening may make more sense.

An unfinished basement wall has the same three choices. Spray foam on the concrete keeps the studs away from the cold surface and gives up the least floor space. Foam board glued to the concrete does close to the same job for less money, with more cutting and more seam tape. Batts behind poly are cheapest, but any moisture coming through the concrete ends up trapped against the wall. The basement insulation page lays them side by side. We would put board or foam against the concrete. The decision is yours.

How far we come

Etobicoke is 18.9 km from us in a straight line and inside the area our crew covers. We measure and quote here the same way we do everywhere else.

There are no neighbourhood pages for Etobicoke on this site yet, so this page covers the whole area, central Etobicoke included.

Air sealing, top-ups and removal in Etobicoke

Air sealing is listed next to spray foam on our home page. If pot lights, plumbing stacks or the attic hatch are letting warm air up into your attic, we close those gaps with foam or caulk before anything else. Insulation laid over an open gap just lets the air keep moving through it.

When the attic floor is short of depth, an attic top-up of blown fibreglass over the existing layer is the simpler job, not foam. A newer house that already has a full layer up there may need nothing, and if so we will tell you. If we do top up, we put baffles in at the eaves and depth markers on the joists.

Old attic insulation that is wet or has had rodents nesting in it needs insulation removal before anything new goes in. If something looks like vermiculite, we stop and leave it alone, and we recommend having a qualified lab or abatement firm test it before any work goes ahead.

About Etobicoke: Etobicoke, ON on Wikipedia ยท Etobicoke on Google Maps

FAQ

Insulation questions from Etobicoke

Yes. Our crew installs closed-cell spray foam on rim joists, basement walls and garage ceilings in Etobicoke houses. We measure the spot first and lay foam out next to foam board and batts, so you can compare before you choose.

Yes, when the joist bays can be reached, closed-cell spray foam is what we would pick for a rim joist. It fills each bay, seals the gap at the sill plate and keeps damp basement air off the cold framing. If the basement ceiling is finished and drywall would have to come down, foam board through a smaller opening may be the better choice.

Etobicoke is about 19 km from us and inside the area our crew covers. We measure and write up a quote for an Etobicoke house the same way we would anywhere else.

Get a quote

Request an insulation visit in Etobicoke

Call (437) 563-1419 or send the form, and tell us what you notice in the house: a cold floor over the garage, a draft at the baseboard, a damp smell in the basement. We measure the spots that matter and give you a written quote with the options side by side.

Call Text Quote